Images are representations only.
Series 2000 Magnehelic Differential Pressure Gauge
Brand: Dwyer Instruments, LLCSelect the Series 2000 Magnehelic® Gauge for a versatile low differential pressure gage with a wide choice of 81 models and 27 options to choose from.
Using Dwyer's simple, frictionless Magnehelic® gage movement, it quickly indicates air or noncorrosive gas pressures - either positive, negative (vacuum) or differential.
The design resists shock, vibration, over-pressures and is weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage option for an accuracy within 1% of full scale, located below in the Product Configurator.
Also included with the –HA option at no extra cost are a mirrored scale overlay and a 6 point calibration certificate.
Note: May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.
Features- Easy to read gage through undistorted plastic face permits viewing from far away
- Patented design provides quick response to pressure changes means no delay in assessing critical situations
- Durable and rugged housing and high-quality components combine to provide longservice life and minimized down-time
- High accuracy option is twice as accurate as the standard Magnehelic® gage.
- Bezel provides flange for flush mounting in panel.
- Clear plastic face is highly resistant to breakage. Provides undistorted viewing of pointer and scale.
- Precision litho-printed scale is accurate and easy to read.
- Red tipped pointer of heat treated aluminum tubing is easy to see. It is rigidly mounted on the helix shaft.
- Pointer stops of molded rubber prevent pointer over-travel without damage.
- "Wishbone" assembly provides mounting for helix, helix bearings and pointer shaft.
- Jeweled bearings are shock-resistant mounted; provide virtually friction-free motion for helix. Motion damped with high viscosity silicone fluid.
- Zero adjustment screw is conveniently located in the plastic cover, and is accessible without removing the cover. O-ring seal provides pressure tightness.
- Helix is precision made from an alloy of high magnetic permeability. Mounted in jeweled bearings, it turns freely, following the magnetic field to move the pointer across the scale.
- Calibrated range spring is flat spring steel. Small amplitude of motion assures consistency and long life. It reacts to pressure on diaphragm. Live length adjustable for calibration.
- Silicone rubber diaphragm with integrally molded O-ring is supported by front and rear plates. It is locked and sealed in position with a sealing plate and retaining ring. Diaphragm motion is restricted to prevent damage due to overpressures.
- Die cast aluminum case is precision made and iridite-dipped to withstand 168 hour salt spray corrosion test. Exterior finished in baked dark gray hammerloid. One case size is used for all standard pressure options, and for both surface and flush mounting.
- OVERPRESSURE PROTECTION
- Blowout plug is comprised of a rubber plug on the rear which functions as a relief valve by unseating and venting the gage interior when over pressure reaches approximately 25 psig (1.7 bar). To provide a free path for pressure relief, there are four spacer pads which maintain 0.023" clearance when gage is surface mounted. Do not obstruct the gap created by these pads. The blowout plug is not used on models above 180" of water pressure, medium or high pressure models, or on gages which require an elastomer other than silicone for the diaphragm. The blowout plug should not be used as a system overpressure control. High supply pressures may still cause the gage to fail due to over pressurization, resulting in property damage or serious injury. Good engineering practices should be utilized to prevent your system from exceeding the ratings of any component.
- O-ring seal for cover assures pressure integrity of case.
- Samarium Cobalt magnet mounted at one end of range spring rotates helix without mechanical linkages.
Specifications
Brand
Accuracy
- ± 2 % of Full Scale at 21.1° C (70° F)
Approvals & Certifications
- EU Directive 2011/65/EU (RoHS II)
Diaphragm Material
- Silicone Rubber
Enclosure, Body Material
- Aluminum Die Cast
- Bezel, with Acrylic Cover
Media
- Air
- Non-Combustible, Compatible Gases (Natural Gas Option Available)
NPT Connection
- 1/8” NPT Female
Overpressure & Static Pressure Limits
- Overpressure: Relief Plug Opens at Approximately psig: 25 (kPa: 172, bar: 1.72)
Pressure Range
- cm WC: 0 to 300
- cm WC: -15 to 0 to 15 Zero Center Ranges
- Inches WC: 0 to 250
- Inches WC: -15 to 0 to 15 Zero Center Ranges
- kPa: 0 to 30
- kPa: -15 to 0 to 1.5 Zero Center Range
- mmWC: 0 to 300
- mmWC: -10 to 0 to 10 Zero Center Ranges
- Pa: -10 to 1,000
- Pa: -500 to 0 to 500 Zero Center Ranges
- psi: 0 to 30
Sensor Orientation
- Diaphragm in Vertical Position
Size
- Dial: 4” (100 mm)
Temperature Range
- -6.67° to 60° C (20° to 140° F)
- Filter Monitoring
- Air Velocity with Dwyer Pitot Tube
- Blower Vacuum Monitoring
- Fan Pressure Indication
- Duct, Room or Building Pressures
- Clean Room Positive Pressure Indication